How many yards for draperies

This means that as you cut each panel to sew, you may have to skip ahead until the pattern starts repeating again. A inch vertical repeat may mean that you may have to skip over up to 23 inches of fabric in between each panel cutting. Speaking of width, what if the drapes need to be wider than 50 inches? Most people are used to drapes that are only 50 inches wide flat. But if your aim is to have more fullness and to get that designer look, I refer you back to the guide and calculator again to figure out how wide each drape needs to be.

If each drape needs to be wider than 50 inches, simply go back to the calculations above and account for the extra panels needed. The single width pair that needed 7. You may be tempted to buy less fabric to save on your project, but I encourage you not to do this. For best results, consult your sewing professional. Drapery Yardage Calculator Please enter all measurements in inches:. Select a fullness depending on your desired look: Flat fullness will have a flat look when drapes are pulled across the window.

Standard fullness will use 2 times more fabric. Width of Desired Drape or Rod. Length of Drape. Repeat of Fabric. The rule of thumb make sure that the lining is thick enough so that the fabric does not have a see-through effect even with a lining. Your email address will not be published. Notify me of followup comments via e-mail. You can also subscribe without commenting. Selecting performance fabrics, such as Crypton for your couch or chairs goes a long way in preserving your sanity as a parent.

All rights reserved. The material on this site may not be reproduced, distributed, transmitted, cached, or otherwise used, except as expressly permitted in writing by My Decorating Tips. Start Here Hello! What is the cost of the fabric for those pretty window curtains I want to make? The first step is to measure the exact height of the curtains and you need to start at the rod location.

Then you need to decide if the curtains are going to go all the way to the floor or stop somewhere in between. Measure to that point The next step is to measure the width of your curtains and again you measure your rod to get the right figure. Next, you double the width measurement so if your window is 36 inches wide you go to 72 inches for 2 panels. Add 1 inch for seam allowance and 6 inches for length allowance. If the length is 84 inches then you need two 37 by inch panels of fabric.

Since curtain fabric comes in 36 inch wide panels, you divide by 36 and you will get a net result of 5 yards needed to make those curtains. You are in luck as there are several easy access to curtain fabric calculators online. These calculators take the work out of knowing how much material you need. Plus, it is easy to change the dimensions when you are working with more than one size of window. The first calculator can be found at this link and the second is found here , while the third is easily found at this third link.

Just pick the one that is easiest for you to use or use all three to make sure each one is accurate and provide you with the correct results. For 2 of the three, you can switch between inches and centimeters at a push of a button.

When you measure you have to start and end with the rod. It takes several inches of fabric up above the window, generally, and that extra amount of fabric must be taken into account. Then when measuring for the width you follow the rod again. You do this because sometimes the curtains you have extended past the window width and you have to take into consideration those inches as well. One thing that is on your side is that curtain fabrics come in several different widths. This allows you to plan your sewing better and cut down on your workload.

Just remember to add in the seam or hem allowance. Those allowances can go anywhere from 1 to 8 inches depending on the style of your curtains. Once you have those measurements finding out how much fabric you need to buy is very simple.

The measuring process is the same as measuring for regular curtains except for a couple of differences. The length is standard and you do not need to worry about that measurement. It is the width you need to be concerned about. When measuring the width you do not have to measure the length of the finials unless there are return brackets. Next, add 12 inches for the panel overlap in the center of the window. Once you have that total, multiply it by 2. Then you divide that total by the number of inches of the fabric you have chosen to use.

So if the width is 60 inches you divide the total by 60 and round up if necessary.